A method to analyze the axially symmetric problem of composite thick tubes with arbitrary angles

GU Fuwei; ZHU Xiaolei; LU Xiaofeng; LIU Yang; FANG Daining; LI Li

doi:10.13801/j.cnki.fhclxb.20210401.001

Volume 39 Issue 2

Feb. 2022

Turn off MathJax

Article Contents

Article Navigation > Acta Materiae Compositae Sinica > 2022 > 39(2): 802-811

GU Fuwei, ZHU Xiaolei, LU Xiaofeng, et al. A method to analyze the axially symmetric problem of composite thick tubes with arbitrary angles[J]. Acta Materiae Compositae Sinica, 2022, 39(2): 802-811. doi: 10.13801/j.cnki.fhclxb.20210401.001

Citation:

GU Fuwei, ZHU Xiaolei, LU Xiaofeng, et al. A method to analyze the axially symmetric problem of composite thick tubes with arbitrary angles[J]. Acta Materiae Compositae Sinica, 2022, 39(2): 802-811. doi: 10.13801/j.cnki.fhclxb.20210401.001

Citation:

PDF( 4555 KB)

A method to analyze the axially symmetric problem of composite thick tubes with arbitrary angles

doi: 10.13801/j.cnki.fhclxb.20210401.001

GU Fuwei^1
,,
ZHU Xiaolei^{1
,
,},
LU Xiaofeng¹,
LIU Yang^1
,,
FANG Daining²,
LI Li³

1.
School of Mechanical and Power Engineering, Nanjing Tech University, Nanjing 211816, China
2.
Institute of Advanced Structure Technology, Beijing Institute of Technology, Beijing 100081, China
3.
China Ship Development and Design Center, Shanghai 201108, China

Received Date: 2021-02-09
Accepted Date: 2021-03-19
Rev Recd Date: 2021-03-11

Available Online: 2021-04-01

Publish Date: 2022-02-01

Abstract

Abstract

A method was proposed to analysis the axisymmetric problem of composite tubes made up of winding layers with arbitrary angles. The traditional Lekhnitskii theory can obtain the exact elastic solution of the thick composite tubes with common winding layers. However, when there are 0° winding layers or isotropic layers in the thick walled tubes, singular parameters will appear in the both special layers. And the discontinuity condition between the special layer and the common layer could not be satisfied. Therefore, the reasons for the existence of singular parameters in special layers were discussed. Then, the continuity analysis and limit calculation of these parameters were carried out, so that the problem of parameter singularity was solved and the application of Lekhnitskii theory was extended to composite thick tubes with arbitrary angles. Finally, the mechanical responses of different compo-site tubes were analyzed by ABAQUS, and the results of finite element calculation were basically consistent with the developed theoretical results.
- composite material,
- axisymmetric problem,
- winding angles,
- thick tubes,
- theoretical analysis
Long Abstrsct
Innovation Points

FullText(HTML)

References(25)

References

[1]	VASILIEV V, BARYNIN V A, RASIN A F. Anisogrid lattice structures-survey of development and application[J]. Composite Structures,2001,54(2):361-370.
[2]	VASILIEV V, BARYNIN V A, RASIN A F. Anisogrid composite lattice structures development and aerospace applications[J]. Composite Structures,2012,94(3):1117-1127. doi: 10.1016/j.compstruct.2011.10.023
[3]	FAN Hualin, FANG Daining, CHEN Liming, et al. Manufacturing and testing of a CFRC sandwich cylinder with Kagome cores[J]. Composites Science and Technology,2009,69(15-16):2695-2700. doi: 10.1016/j.compscitech.2009.08.012
[4]	FAN H L, JING F N, FANG D N, et al. Mechanical properties of hierarchical cellular materials, Part I: Analysis[J]. Composites Science & Technology,2008,68:3380-3387. doi: 10.1016/j.compscitech.2008.09.022
[5]	郑津洋, 李静媛, 黄强华. 车用高压燃料气瓶技术发展趋势和我国面临的挑战[J]. 压力容器, 2014(2):43-51. doi: 10.3969/j.issn.1001-4837.2014.02.007 ZHENG Jinyang, LI Jingyuan, HUANG Qianghua. Technology trends of high pressure vehicle fuel tanks and challenges for China[J]. Pressure Vessel Technology,2014(2):43-51(in Chinese). doi: 10.3969/j.issn.1001-4837.2014.02.007
[6]	中华人民共和国国家质量监督检验检疫总局、中国国家标准化管理委员会. 车用压缩氢气铝内胆碳纤维全缠绕气瓶: GB/T 35544—2017[S]. 北京: 中国标准出版社, 2017. Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China, China National Standardization Management Committee. FuIly-wrapped carbon fiber reinforced cylinders with an aluminum liner for the on-board storage of compressed hydrogen as a fuel for land vehicles: GB/T 35544—2017[S]. Beijing: China Standards Press, 2017(in Chinese).
[7]	顾付伟, 顾周越, 朱晓磊, 等. 一种无焊缝连接金属内衬复合材料压力容器的制备工艺及其液压实验[J]. 复合材料学报, 2021, 38(1):198-208. GU Fuwei, GU Zhouyue, ZHU Xiaolei, et al. The design and hydraulic tests of a metal liner composite overwrapped pressure vessels with seamless connection technology[J]. Acta Materiae Compositae Sinica,2021,38(1):198-208(in Chinese).
[8]	蔡光胜, 张锦光, 毛戈. 碳纤维复合材料直升机传动轴设计研究[J]. 玻璃钢/复合材料, 2019(10):71-75. CAI Guangsheng, ZHANG Jinguang, MAO Ge. Design and research of carbon fiber composite helicopter drive shaft[J]. Fiber Reinforced Plastics/Composites,2019(10):71-75(in Chinese).
[9]	胡晶, 李晓星, 张天敏, 等. 碳纤维复合材料传动轴承扭性能优化设计[J]. 复合材料学报, 2009, 26(6):177-181. doi: 10.3321/j.issn:1000-3851.2009.06.030 HU Jing, LI Xiaoxing, ZHANG Tianmin, et al. Design optimization on torsion property of carbon-fiber composite drive shaft[J]. Acta Materiae Compositae Sinica,2009,26(6):177-181(in Chinese). doi: 10.3321/j.issn:1000-3851.2009.06.030
[10]	沈观林. 复合材料力学[M]. 北京: 清华大学出版社, 2013. SHEN Guanlin. Mechanics of composite materials[M]. Beijing: Tsinghua University Press, 2013(in Chinese).
[11]	JIANG S Y, SUN F, FAN H L. Multi-failure theory of composite orthogrid sandwich cylinder[J]. Aerospace Science and Technology,2017,70(11):520-525.
[12]	JIANG S Y, SUN F, FAN H L, et al. Fabrication and testing of composite orthogrid sandwich cylinder[J]. Composites Science & Technology,2017,142(4):171-179.
[13]	XIA M, TAKAYANAGI H, KEMMOCHI K. Analysis of multi-layered filament-wound composite pipes under internal pressure[J]. Composite Structures,2001,53(4):483-491. doi: 10.1016/S0263-8223(01)00061-7
[14]	ROY A K, TSAI S W. Design of thick composite cylinders[J]. Journal of Pressure Vessel Technology,1988,110:255-262. doi: 10.1115/1.3265597
[15]	HYER M W. Hydrostatic response of thick laminated composite cylinders[J]. Journal of Reinforced Plastics and Composites,1988,7(4):321-340. doi: 10.1177/073168448800700402
[16]	LEKHNITSKII S G. Theory of elasticity of an anisotropic elastic body[M]. Moscow: Mir Publishers, 1981: 215-262.
[17]	STROH A N. Dislocations and cracks in anisotropic elasticity[J]. Philosophical Magazine,1958,3:625-646. doi: 10.1080/14786435808565804
[18]	ZU L, WANG J, LI S. Analysis of multi-layered thick-walled filament-wound hydrogen storage vessels[J]. International Journal of Hydrogen Energy,2014,39(36):21083-21096. doi: 10.1016/j.ijhydene.2014.10.075
[19]	TING T C T. Anisotropic elasticity theory and applications[M]. Oxford: Oxford University Press, 1996: 118-163.
[20]	JOLICOEUR C, CARDOU A. Analytical solution for bending of coaxial orthotropic cylinders[J]. Journal of Engineering Mechanics,1994,120(12):2556-2574. doi: 10.1061/(ASCE)0733-9399(1994)120:12(2556)
[21]	张灿辉, 张建霖, 柯淼宏, 等. 采用独立双应力函数分析纯弯曲复合材料厚壁管[J]. 厦门大学学报(自然科学版), 2017, 56(6):900-906. ZHANG Canhui, ZHANG Jianlin, KE Miaohong, et al. Analysis of composite material thick walled tubes subjected to pure bending loading using two stress functions independent to each other[J]. Journal of Xiamen University (Natural Science),2017,56(6):900-906(in Chinese).
[22]	柯淼宏. 纯弯曲复合材料组合管统一联系参数法的进一步研究[D]. 厦门: 厦门大学, 2017. KE Miaohong. More investigation of unified-connected-parameter method for composite material combined tubes under pure bending loading[D]. Xiamen: Xiamen University, 2017(in Chinese).
[23]	刘沛. 复合材料厚壁管弯曲性能分析的统一参数法及杂交应力有限元最佳假设应力场构造的定量方法[D]. 厦门: 厦门大学, 2014. LIU Pei. The unified-parameter method for bending perfor-mance analysis of composite thick tube as well as the quanti-tave method to determine the optimal assumed stress fields for hybrid stress finite elements[D]. Xiamen: Xiamen University, 2014(in Chinese).
[24]	ZHANG C H, HOA S V. Limit based approach to the stress analysis of cylindrically orthotropic composite cylinders (0/90) subjected to pure bending[J]. Composite Structure,2012,94:2610-2619. doi: 10.1016/j.compstruct.2012.02.030
[25]	ZHANG C H, HOA S V, LIU P. A method to analyze the pure bending of tubes of cylindrically anisotropic layers with arbitrary angles including 0 and 90[J]. Composite Structure,2014,109:57-67. doi: 10.1016/j.compstruct.2013.10.038