Interface characteristics study of Al/Mg laminated composite sheets by multi-passes RHR
-
摘要: 为研究热辊轧制对层状复合材料组织性能的影响，本文采用多道次热辊轧制工艺制备了Al/AZ31B/Al多层复合板材，通过OM、XRD、SEM及设计模具测试，分析了不同压下率、退火温度对复合板材界面微观形貌和结合性能的影响规律。结果表明：热辊轧制兼具变形和促进扩散层的形成双重作用，大压下率复合板材结合界面形成不连续的扩散层。随着压下率增加，结合面由平直逐渐呈显著的“波浪”型，相近的剪切坡度成对出现且角度相近，过大压下率导致异质材料变形过程难以协调，镁层厚度方向减薄明显的部分区域出现裂纹。退火后Al/Mg结合界面形成了更有效的冶金结合，随着退火温度的升高，扩散层厚度不断增加且有分层现象，金属间化合物为Al3Mg2(β相)和Mg17Al12(γ相)。剥离形貌为准解理断裂，退火温度过高时，板条状的金属间化合物变得更加粗大，两金属板材会从金属间化合物层开裂。在压下率为60%~70%，退火温度为200~250℃时有利于热辊轧制复合板材的结合强度提升。Abstract: In order to study the effect of rolling with heated roll on the microstructure and properties of laminated composites, Al/AZ31B/Al laminated composites were fabricated by multi-passes RHR in this paper. The influences of different reduction and annealing temperatures on the interfacial morphology and bonding properties of the composites were analyzed by OM, XRD, SEM and design mold tests. The results show that the rolling with heated roll has a deformation and promoting the formation of a diffusion layer, and the discontinuous diffusion layer is formed at bonding interface of composite sheets under high reduction. With the increase of the reduction, the bonding surface gradually presents a significant “wave” type from flat, and the shear slopes occur in pairs with similar angles. The excessive reduction leads to difficulty in the coordination of the deformation process of heterogeneous materials, and the cracks appear in some areas of the decreasing direction of the magnesium layer thickness. After annealing, the Al/Mg bonding interface forms more effective metallurgical bonding. With the increase of annealing temperature, the thickness of the diffusion layer increases, and there is a delamination phenomenon. The intermetallic compounds are Al3Mg2 (β phase) and Mg17Al12 (γ phase). The peeling morphology is quasi-cleavage fracture. When the annealing temperature is too high, the sheet-shaped intermetallic compound becomes thicker, and the two metal plates will be crackled from the intermetallic compound layer. When the reduction is 60%-70% and the annealing temperature is 200-250℃, the bonding strength of the composite sheet by multi-passes rolling with heated roll is improved.
-
图 1 Al/Mg/Al层状复合板轧制示意图
Figure 1. Schematic diagram of rolling Al/Mg/Al laminated composite plate
图 2 剪切试样及模具示意图
Figure 2. Schematic diagram of shear sample and die
RD—Rolling direction; ND—Normal direction
图 3 不同压下率Al/Mg/Al复合板材结合界面光学显微组织
Figure 3. Optical microstructure of the bonding interface of Al/Mg/Al laminated sheets with different reduction
图 4 不同退火温度下Al/Mg/Al复合板材Mg层光学显微组织
Figure 4. Optical microstructure of Mg layer in Al/Mg/Al laminated composite at different annealing temperatures
图 5 不同压下率下Al/Mg/Al复合板材结合界面SEM图像
Figure 5. SEM images of the bonding interface of Al/Mg/Al laminated composites at different reduction
图 6 不同退火温度Al/Mg/Al复合板材结合界面的SEM图像
Figure 6. SEM images of the bonding interface of Al/Mg/Al laminated composites at different annealing temperatures
图 7 不同退火温度的Al/Mg结合界面EDS图谱
Figure 7. EDS spectra of the Al/Mg bonding interface at different annealing temperature
l1 and l3—Boundary between the two metal compounds; l2—Boundary between Al matrix and intermetallic compound; l4—Boundary between Mg matrix and intermetallic compound
图 8 Al/Mg/Al复合板材Al/Mg结合界面XRD结果
Figure 8. XRD phase analysis of Al/Mg bonding interface of Al/Mg/Al composite plate
图 9 Al/Mg/Al复合板材的Al/Mg结合界面EDS图像
Figure 9. EDS images of Al/Mg bonding interface of Al/Mg/Al laminated composite
图 10 300℃退火后镁层基体剥离面SEM图像及EDS图谱
Figure 10. SEM images and EDS spectra of magnesium layer matrix peeling surface after annealing at 300℃
TD—Transverse direction
图 11 不同退火温度下Al/Mg/Al复合板材结合界面经剥离后的镁层SEM图像
Figure 11. SEM images of Mg layer after peeling off the bonding interface of Al/Mg/Al laminated composite at different annealing temperatures
-
[1] AGARWAL S, CURTIN J, DUFFY B, et al. Biodegradable magnesium alloys for orthopaedic applications: A review on corrosion, biocompatibility and surface modifications[J]. Materials Science& Engineering C,2016,68:948-963. doi: 10.1016/j.msec.2016.06.020 [2] ZHANG Q, LI Q A, CHEN X Y. Research progress of ultrafine grained magnesium alloy prepared by equal channel angular pressing[J]. Materials Research Express,2021,8(2):022001. [3] 常海, 徐超, 胡小石. 累积叠轧纯Mg/ZK60镁合金层状金属复合材料的组织与性能[J]. 复合材料学报, 2019, 36(1):178-185.CHANG Hai, XU Chao, HU Xiaoshi. Microstructure evolution and mechanical properties of Mg/ZK60 laminated composite fabricated by accumulated roll-bonding[J]. Acta Materiae Compositae Sinica,2019,36(1):178-185(in Chinese). [4] 陈振华. 镁合金[M]. 北京: 化学工业出版社, 2004.CHEN Zhenhua. Magnesium alloys[M]. Beijing: Chemical Industry Press, 2004(in Chinese). [5] 祖国胤. 层状金属复合材料制备理论与技术[M]. 沈阳: 东北大学出版社, 2013: 1-6.ZU Guoyin. Layered metal composite material preparation theory and technology[M]. Shenyang: Northeastern University Press, 2013: 1-6(in Chinese). [6] SURYANARAYANA C, AL-AQEELI N. Mechanically alloyed nanocomposites[J]. Progress in Materials Science,2013,58(4):383-502. doi: 10.1016/j.pmatsci.2012.10.001 [7] 梅瑞斌. 金属塑性加工过程有限元数值模拟及软件应用[M]. 北京: 科学出版社, 2020: 4.MEI Ruibin. Finte element simulation and software application in metal forming[M]. Beijing: Science Press, 2020: 4(in Chinese). [8] CHEN L, TANG J W, ZHAO G Q, et al. Fabrication of Al/Mg/Al laminate by a porthole die co-extrusion process[J]. Journal of Materials Processing Technology,2018,258:165-173. doi: 10.1016/j.jmatprotec.2018.03.027 [9] 陈琦, 迟之东. 镁/铝复合板材制备工艺及性能研究[J]. 有色金属加工, 2015, 44(1):26-28. doi: 10.3969/j.issn.1671-6795.2015.01.008CHEN Qi, CHI Zhidong. Study of preparation and properties of Mg/Al composite sheet[J]. Nonferrous Metals Processing,2015,44(1):26-28(in Chinese). doi: 10.3969/j.issn.1671-6795.2015.01.008 [10] CHANG H, ZHENG M Y, GAN W M, et al. Texture evolution of the Mg/Al laminated composite fabricated by the accumulative roll bonding[J]. Scripta Materialia,2009,61(7):717-720. doi: 10.1016/j.scriptamat.2009.06.014 [11] CHANG H, ZHENG M Y. Effect of intermetallic compounds on the fracture behavior of Mg/Al laminated composite fabricated by accumulative roll bonding[J]. Rare Metal Materials and Engineering,2016,45(9):2242-2245. doi: 10.1016/S1875-5372(17)30010-3 [12] WU K, CHANG H, MAAWAD E, et al. Microstructure and mechanical properties of the Mg/Al laminated composite fabricated by accumulative roll bonding (ARB)[J]. Mater-ials Science and Engineering: A,2010,527(13-14):3073-3078. doi: 10.1016/j.msea.2010.02.001 [13] MOTEVALLI P D, EGHBALI B. Microstructure and mechanical properties of Tri-metal Al/Ti/Mg laminated composite processed by accumulative roll bonding[J]. Materials Science and Engineering: A,2015,628:135-142. doi: 10.1016/j.msea.2014.12.067 [14] CHEN M C, KUO C W, CHANG C M, et al. Diffusion and formation of intermetallic compound during accumulative roll-bonding of Al/Mg alloys[J]. Materials Transactions,2007,48(10):2595-2598. doi: 10.2320/matertrans.MD200718 [15] ZHANG X P, YANG T H, CASTAGNE S, et al. Microstructure; bonding strength and thickness ratio of Al/Mg/Al alloy laminated composites prepared by hot rolling[J]. Materials Science and Engineering: A,2011,528(4-5):1954-1960. doi: 10.1016/j.msea.2010.10.105 [16] WEI A L, LIU X H, DONG L, et al. Binding property of Al/Mg/Al thin plates fabricated by one-pass hot rolling with different reduction ratios, temperatures and annealing treatments[J]. Rare Metals,2018,37(2):136-142. doi: 10.1007/s12598-015-0519-0 [17] XU Z H, TANG G Y, TIAN S Q, et al. Research of electroplastic rolling of AZ31Mg alloy strip[J]. Journal of Materials Processing Tech,2006,182(1):128-133. [18] 官磊. 电致塑性轧制AZ31镁合金的变形机制及其组织和性能研究[D]. 北京: 清华大学, 2010.GUAN Lei. Microstructure evolution, mechanical properties and mechanism analysis of AZ31 magnesium alloy by electroplastic rolling[D]. Beijing: Tsinghua University, 2010(in Chinese). [19] 孙颖, 韩晶. 内加热轧辊对镁合金叠轧板材轧制实验的改进研究[J]. 山西冶金, 2018, 41(1):1-2.SUN Ying, HAN Jing. Study on the improvement of experiment of pack rolling on magnesium alloy by internal heating rollers[J]. Shanxi Metallurgy,2018,41(1):1-2(in Chinese). [20] KIM W Y, KIM W J. Fabrication of ultrafine-grained Mg-3Al-Zn alloy sheets using a continuous high-ratio differential speed rolling technique[J]. Materials Science & Engineering A,2014,594:189-192. [21] YU H L, YU Q B, KANG J W, et al. Investigation on tempera-ture change of cold magnesium alloy strips rolling process with heated roll[J]. Journal of Materials Engineering and Performance,2012,21(9):1841-1848. doi: 10.1007/s11665-011-0091-1 [22] SUN T, LI J P. Method for outlet temperature control during warm rolling of AZ31 sheets with heated rolls[J]. ISIJ International,2017,57(9):1577-1585. doi: 10.2355/isijinternational.ISIJINT-2016-744 [23] 梅瑞斌, 包立, 张欣, 等. 一种镁合金带材热辊加热轧制装置及方法: 中国, CN201610077523.5[P]. 2016-04-27.MEI Ruibin, BAO Li, ZHANG Xin, et al. A hot roller heating rolling device and method for magnesium alloy strip: China, CN201610077523.5[P]. 2016-04-27(in Chinese). [24] BAO L, QI X W, MEI R B, et al. Investigation and modeling of work roll temperature in induction heating by finite element method[J]. Journal of the Southern African Institute of Mining and Metallurgy,2018,118(7):735-743. [25] 彭大署. 金属塑性加工原理[M]. 长沙: 中南大学出版社, 2004.PENG Dashu. Metal plastic processing principle[M]. Changsha: Central South University Press, 2004(in Chinese). [26] BRENNAN S, BERMUDEZ K, KULKARNI N S, et al. Interdiffusion in the Mg-Al system and intrinsic diffusion in beta-Mg2Al3[J]. Metallurgical and Materials Transactions A,2012,43(11):4043-4052. doi: 10.1007/s11661-012-1248-8 -
下载:
点击查看大图
计量
- 文章访问数: 910
- HTML全文浏览量: 544
- PDF下载量: 54
- 被引次数: 0
