Preparation and properties of Al2O3/MoSi2 coating on Al2O3 base porous insulation materials
-
摘要: 采用刷涂法在Al2O3基多孔隔热材料表面制备Al2O3/MoSi2涂层，涂层以硅溶胶作为粘结剂，纳米Al2O3与Al2O3纤维作为耐高温组分，MoSi2为高发射率组分。通过SEM、XRD对Al2O3/MoSi2涂层微观表面结构、物相组成进行分析。研究纳米Al2O3与Al2O3纤维的质量比和MoSi2含量对Al2O3/MoSi2涂层耐温性能的影响，并对Al2O3/MoSi2涂层的抗热震性能、发射率进行表征。结果表明，当纳米Al2O3与Al2O3纤维的质量比小于1∶1时，热考核后Al2O3/MoSi2涂层表面无裂纹产生；当纳米Al2O3与Al2O3纤维的质量比在1∶2~1∶4之间时，Al2O3/MoSi2涂层中的纤维网络较完整。MoSi2的含量为20%时，Al2O3/MoSi2涂层抗热震实验循环25次后表面保持完好，热考核后在2.5~25 μm波段的平均发射率在0.85左右，具有较高的发射率。
-
关键词:
- Al2O3基多孔隔热材料 /
- 抗热震性能 /
- 高发射率 /
- 涂层 /
- 纳米纤维
Abstract: The Al2O3/MoSi2 coating on Al2O3 base porous insulation materials was prepared by brushing method. Silica sol served as binder and MoSi2 as high emissivity component while nano Al2O3 and Al2O3 fiber were used as high temperature component. The surface morphology and crystalline structure of the Al2O3/MoSi2 coating were analyzed by SEM and XRD. The effects of the mass ratio of nano Al2O3 to Al2O3 fiber and the content of MoSi2 on thermal endurance of the Al2O3/MoSi2 coating were studied. Thermal shock resistance and radiative property of the Al2O3/MoSi2 coating were investigated. The results indicate that there is no cracks on the Al2O3/MoSi2 coating surface when the mass ratio of nano Al2O3 to Al2O3 fiber is less than 1∶1. Fiber-network is relatively integrated on the Al2O3/MoSi2 coating at the mass ratio of nano Al2O3 to Al2O3 fiber of 1∶2–1∶4. The best content of MoSi2 in the Al2O3/MoSi2 coating is 20%. When the content of MoSi2 is 20%, the surface of Al2O3/MoSi2 coating remains unbroken after 25 thermal shock cycles. The Al2O3/MoSi2 coating has high emissivity which is around 0.85 at 2.5–25 μm after heat treatment. -
图 1 不同纳米Al2O3与Al2O3纤维质量比的Al2O3涂层热考核后的SEM图像
Figure 1. SEM images of Al2O3 coating with different mass ratios of nano Al2O3 to Al2O3 fiber after heat treatment
图 2 不同MoSi2含量的Al2O3/MoSi2涂层热考核后的SEM图像
Figure 2. SEM images of Al2O3/MoSi2 coating with different MoSi2 contents after heat treatment
图 3 不同MoSi2含量的Al2O3/MoSi2涂层热考核后的照片
Figure 3. Photographs of Al2O3/MoSi2 coating with different MoSi2 contents after heat treatment
图 4 不同MoSi2含量的Al2O3/MoSi2涂层热考核后的XRD图谱
Figure 4. XRD patterns of Al2O3/MoSi2 coatings with different MoSi2 contents after heat treatment
图 5 MoSi2含量为20%的Al2O3/MoSi2涂层1200℃抗热震循环实验前表面((a)、(b))、截面(c)及实验后表面((d)、(e))的SEM图像
Figure 5. SEM images of surface ((a), (b)) and cross section (c) before thermal shock cycles and surface after thermal shock cycles ((d), (e)) of Al2O3/MoSi2 coating with MoSi2 content of 20%
图 6 MoSi2含量为20%的Al2O3/MoSi2涂层抗热震循环前后的XRD图谱
Figure 6. XRD patterns of Al2O3/MoSi2 coating with MoSi2 content of 20% before and after thermal shock cycles
-
[1] LUO Y, JIANG Y G, FENG J Z, et al. Synthesis of white cement bonded porous fumed silica-based composite for thermal insulation with low thermal conductivity via a facile cast-in-place approach[J]. Construction and Building Materials,2019,206:620-629. [2] SUN Y F, GAO P W, GENG F, et al. Thermal conductivity and mechanical properties of porous concrete materials[J]. Materials Letters,2017,209:349-352. [3] GAO H, LIU H, LIAO L B, et al. Improvement of performance of foam perlite thermal insulation material by the design of a triple-hierarchical porous structure[J]. Energy and Buildings,2019,200:21-30. doi: 10.1016/j.enbuild.2019.07.010 [4] 周伟, 肖鹏, 李杨, 等. 炭/炭复合材料表面SiC/ZrSiO4-SiO2复合涂层的抗氧化性能与红外发射特性研究[J]. 稀有金属与材料工程, 2017, 46(11):3479-3484.ZHOU Wei, XIAO Peng, LI Yang, et al. Anti-oxidation and infrared emissivity property of SiC/ZrSiO4-SiO2 composite coatings on carbon/carbon composites[J]. Rare Metal Materials and Engineering,2017,46(11):3479-3484(in Chinese). [5] WANG Y C, SU D, JI H M, et al. Gradient structure high emissivity MoSi2-SiO2-SiOC coating for thermal protective application[J]. Journal of Alloys and Compounds,2017,703:437-447. doi: 10.1016/j.jallcom.2017.01.317 [6] FEI X A , NIU Y R, JI H, et al. Oxidation behavior of Al2O3 reinforced MoSi2 composite coatings fabricated by vacuum plasma spraying[J]. Ceramics International,2010,36:2235-2239. doi: 10.1016/j.ceramint.2010.05.001 [7] 曾燮榕, 郑长卿, 李贺军, 等. 碳/碳复合材料MoSi2涂层的防氧化研究[J]. 复合材料学报, 1997, 14(3):37-40.ZENG Xierong, ZHENG Changqing, LI Hejun, et al. Properties of oxidation resistant MoSi2 coating of carbon/carbon composites[J]. Acta Materiae Compositae Sinica,1997,14(3):37-40(in Chinese). [8] SHAO G F, LU Y C, WU X D, et al. Preparation and thermal shock resistance of high emissivity molybdenum disilicide-aluminoborosilicate glass hybrid coating on fiber reinforced aerogel composite[J]. Applied Surface Science,2017,416:805-814. doi: 10.1016/j.apsusc.2017.04.184 [9] MEYER M K, AKINC M. Oxidation behavior of boron modified Mo5Si3 at 800–1 300℃[J]. Journal of the American Ceramic Society,1996,79(4):938-944. doi: 10.1111/j.1151-2916.1996.tb08528.x [10] YANG Y, LI M S, XU L, et al. Oxidation behaviours of ZrB2-SiC-MoSi2 composites at 1 800℃ in air with different pressures[J]. Corrosion Science,2019,157:87-97. [11] 周炎哲, 刘敏, 杨焜, 等. 大气等离子喷涂MoSi2-30Al2O3电热涂层的组织结构及性能[J]. 无机材料学报, 2019, 34(6):646-652. doi: 10.15541/jim20180394ZHOU Yanzhe, LIU Min, YANG Kun, et al. Microstructure and property of MoSi2-30Al2O3 electrothermal coating prepared by atmospheric plasma spray[J]. Journal of Inorganic Materials,2019,34(6):646-652(in Chinese). doi: 10.15541/jim20180394 [12] 宋永忠, 樊桢, 李兴超, 等. 碳/碳复合材料SiC/MoSi2/ZrO2涂层体系氧化烧蚀性能[J]. 复合材料学报, 2016, 33(10):2290-2296.SONG Yongzhong, FAN Zhen, LI Xingchao, et al. Oxidation ablation property of carbon/carbon composites SiC/MoSi2/ZrO2 coating system[J]. Acta Materiae Compositae Sinica,2016,33(10):2290-2296(in Chinese). [13] CHU Y H, LI H J, FU Q G, et al. Oxidation protection of C/C composites with a multilayer coating of SiC and Si+SiC+SiC nanowires[J]. Carbon,2012,50(3):1280-1288. doi: 10.1016/j.carbon.2011.10.048 [14] ZHANG X F, ZHOU K S, LIU M, et al. Oxidation and thermal shock resistant properties of Al-modified environmental barrier coating on SiCf/SiC composites[J]. Ceramics International,2017,43(16):13075-13082. doi: 10.1016/j.ceramint.2017.06.167 [15] 焦星剑, 李同起, 张中伟, 等. C/C复合材料的SiC/Si-B4C涂层在500~1 500℃的抗氧化机制[J]. 复合材料学报, 2018, 35(11):3130-3136.JIAO Xingjian, LI Tongqi, ZHANG Zhongwei, et al. Oxidation resistance of SiC/Si-B4C coating on C/C composites at 500–1 500℃ in air[J]. Acta Materiae Compositae Sinica,2018,35(11):3130-3136(in Chinese). [16] 李俊生, 张长瑞, 曹英斌, 等. C/SiC材料表面Si/SiC涂层及其对基底结构的影响[J]. 复合材料学报, 2006, 23(6):144-148. doi: 10.3321/j.issn:1000-3851.2006.06.024LI Junsheng, ZHANG Changrui, CAO Yingbin, et al. Si/SiC coatings on C/SiC composites and their effects on the structure of the substrate[J]. Acta Materiae Compositae Sinica,2006,23(6):144-148(in Chinese). doi: 10.3321/j.issn:1000-3851.2006.06.024 [17] 张凡, 安烜熜, 李文静, 等. 一种纳米隔热材料及其制备方法: 中国, CN 201811409160.6[P]. 2019-02-26.ZHANG Fan, AN Xuancong, LI Wenjing, et al. Nanometer thermal insulation material and preparation method: China, CN 201811409160.6[P]. 2019-02-26 (in Chinese). [18] 常春, 李木森, 陈传中, 等. MoSi2高温氧化层的微观结构[J]. 金属学报, 2003, 39(2):126-130. doi: 10.3321/j.issn:0412-1961.2003.02.003CHANG Chun, LI Musen, CHEN Chuanzhong, et al. Microstructure of high-temperature oxidation layer of molybdenum disilicide[J]. Acta Metallurgica Sinica,2003,39(2):126-130(in Chinese). doi: 10.3321/j.issn:0412-1961.2003.02.003 [19] HUANG J, LI Y, HE X, et al. Enhanced spectral emissivity of CeO2 coating with cauliflower-like microstructure[J]. Applied Surface Science,2012,259:301-305. doi: 10.1016/j.apsusc.2012.07.037 [20] DAHAN N, NIV A, BIENER G, et al. Space-variant polarization manipulation of a thermal emission by a SiO2 subwavelength grating supporting surface phonon-polaritons[J]. Applied Physics Letters,2005,86(19):191102. doi: 10.1063/1.1922084 [21] 李俊峰, 卢鹉, 罗正平, 等. 表面粗糙度对高辐射涂层发射率的影响[J]. 宇航材料工艺, 2013, 43(6):75-78. doi: 10.3969/j.issn.1007-2330.2013.06.014LI Junfeng, LU Wu, LUO Zhengping, et al. Influence of surface roughness on the emissivity of high emissivity coatings[J]. Aerospace Materials & Technology,2013,43(6):75-78(in Chinese). doi: 10.3969/j.issn.1007-2330.2013.06.014 -
下载:
点击查看大图
计量
- 文章访问数: 1883
- HTML全文浏览量: 598
- PDF下载量: 66
- 被引次数: 0
