复合材料多钉连接钉载矢量传感器

张建宇; 刘丰睿; 山美娟; 赵丽滨

doi:10.13801/j.cnki.fhclxb.20150515.002

复合材料多钉连接钉载矢量传感器

1.
北京航空航天大学固体力学研究所, 北京 100191;
2.
北京航空航天大学宇航学院, 北京 100191

基金项目: 国家自然科学基金(11372020)

详细信息

通讯作者:
赵丽滨, 博士, 教授, 博士生导师, 研究方向为计算固体力学、结构力学分析及优化设计、复合材料结构力学。 E-mail: lbzhao@buaa.edu.cn

中图分类号: TB330.1;V214.8
计量
- 文章访问数: 879
- HTML全文浏览量: 73
- PDF下载量: 653
出版历程
- 收稿日期: 2014-11-23
- 修回日期: 2015-04-27
- 刊出日期: 2015-10-14

Instrumented bolt for load vector of composite multi-bolt joints

1.
Institute of Solid Mechanics, Beihang University, Beijing 100191, China;
2.
School of Astronautics, Beihang University, Beijing 100191, China

摘要

摘要: 在总结复合材料多钉连接钉载测试方法的基础上, 针对单向载荷传感器应用中必须已知钉载方向且需要按照钉载方向装设传感器的缺点, 提出了钉载矢量传感器方案。钉载矢量传感器无预设安装角度要求, 能够测量载荷方向;并对钉载矢量传感器的选材、应变片方案及开槽尺寸进行了设计, 制造了钉载矢量传感器。采用复合材料单钉单剪螺栓连接, 分别对钉载矢量传感器测量结果的线性符合性、重复性、安装角度影响以及载荷方向测量能力进行了测试研究。测试结果表明:钉载矢量传感器满足工程上对载荷分配测试的技术要求, 验证了本文所提出的钉载矢量传感器的适用性。
- 复合材料 /
- 多钉连接 /
- 载荷分配 /
- 钉载矢量传感器 /
- 试验测量
Abstract: Based on a brief survey of the test methods for load in composite multi-bolt joints, an instrumented bolt for load vector plan without prearranged installation angle demand and with the capability of load direction measurement is presented to overcome the shortcoming of the existed instrumented bolt that it must be installed according to provided load direction. The material selection, stickup scheme of strain gauges and slot dimensions of the instrumented bolt for load vector were designed, from which the instrumented bolt for load vector was further manufactured. The linearity and repeatability of test results of instrumented bolt for load vector, the effect of the installation angle on the test results and the load direction measurements were experimentally investigated with a single-lap, single-bolt composite joint. The test outcomes show the presented instrumented bolt for load vector satisfies the technical requirements for measuring load distribution of bolts in engineering, which further verifies the suitability of the proposed instrumented bolt for load vector.
- composites /
- multi-bolt joint /
- load distribution /
- instrumented bolt for load vector /
- test measurement

HTML全文

参考文献(0)

施引文献(6)

期刊类型引用(4)

1.	陆毛须，姬晓慧，郝自清，张磊，刘刘. 复杂面内应力状态下平面编织高铝纤维增强氧化铝基复合材料强度及疲劳寿命预测方法. 复合材料学报. 2021(11): 3785-3798 . 本站查看
2.	刘刘，姬晓慧，郝自清，曲宏亮，贺体人. 数字图像相关技术在多孔气凝胶基复合材料弹性力学常数识别中的应用. 北京理工大学学报. 2020(10): 1033-1042 . 百度学术
3.	孙颖，刘俊岭，郑园园，陈利，李嘉禄. 碳/芳纶混编三维编织复合材料拉伸性能. 纺织学报. 2018(02): 49-54 . 百度学术
4.	关蕴奇，姜勇刚，冯军宗，冯坚. 无机纤维增强SiO_2气凝胶隔热复合材料的研究进展. 材料导报. 2017(S1): 429-434 . 百度学术