Structural design and low speed impact performance of cross recessed grid sandwich

CAO Zhongliang; ZHU Hao; DONG Mingjun; HE Qing

doi:10.13801/j.cnki.fhclxb.20220311.001

Volume 40 Issue 2

Feb. 2023

Turn off MathJax

Article Contents

Article Navigation > Acta Materiae Compositae Sinica > 2023 > 40(2): 1190-1207

CAO Zhongliang, ZHU Hao, DONG Mingjun, et al. Structural design and low speed impact performance of cross recessed grid sandwich[J]. Acta Materiae Compositae Sinica, 2023, 40(2): 1190-1207. doi: 10.13801/j.cnki.fhclxb.20220311.001

Citation:

CAO Zhongliang, ZHU Hao, DONG Mingjun, et al. Structural design and low speed impact performance of cross recessed grid sandwich[J]. Acta Materiae Compositae Sinica, 2023, 40(2): 1190-1207. doi: 10.13801/j.cnki.fhclxb.20220311.001

Citation:

PDF( 22681 KB)

Structural design and low speed impact performance of cross recessed grid sandwich

doi: 10.13801/j.cnki.fhclxb.20220311.001

School of Mechanical Engineering, Jiangsu University of Technology, Changzhou 213000, China

Funds: Universities Natural Science Research Major Project of Jiangsu Province (21KJA460004); National Natural Science Foundation of China (51705266)

Received Date: 2022-01-07
Accepted Date: 2022-03-03
Rev Recd Date: 2022-03-02

Available Online: 2022-03-13

Publish Date: 2023-02-15

Abstract

Abstract

Aiming at the problems of low ultimate bearing capacity of traditional grid sandwich structure and easy condensation of water vapor caused by single cell sealing, a cross-locked grid sandwich structure was proposed based on analyzing the microstructure and function of tracheids. Firstly, the minimum volume (minimum mass) and minimum deformation (maximum stiffness) were selected as the optimization objectives, and the second generation non-dominated genetic algorithm (NSGA-II) was used to complete the multi-objective optimization. The three-dimensional Hashin failure criterion and the improved stiffness degradation method were used to establish the finite element analysis model of progressive impact damage for the grated sandwich plate. The failure mechanism and mechanical response of a variety of low speed impact loads to different positions of sandwich structures with different relative densities were studied. Results show that the new type of sandwich structure shows good shock impedance at low speed. Its differences with the core of the spatial distribution, the shock resistance of grille gaps are weaker. Core density increase cannot effectively improve the impact strength of the location. The sandwich structure is much larger than all the damage by impact grid intersection point of the device. Under the influence of different impact location and impact velocity, load-time and displacement-time curves show different typical patterns. The failure of core appears, such as buckling, delamination, bonding stripping and bending deformation, and mixed damage occurs on the front panel of composite material. With the increase of impact velocity, the damage degree of core and panel becomes more serious.
- grid sandwich structure,
- multi-objective optimization,
- low speed impact,
- failure criterion,
- failure mechanism
Long Abstrsct
Innovation Points

FullText(HTML)

References(31)

References

[1]	WEI X Y, LI D F, XIONG J. Fabrication and mechanical behaviors of an all-composite sandwich structure with a hexagon honeycomb core based on the tailor-folding approach[J]. Composites Science and Technology,2019,184:878-894.
[2]	DU Y T, SONG C P, XIONG J, et al. Fabrication and mecha-nical behaviors of carbon fiber reinforced composite foldcore based on curved-crease origami[J]. Composites Science and Technology,2019,174:94-105.
[3]	SUN F F, LAI C L, FAN H L. Failure mode maps for composite anisogrid lattice sandwich cylinders under fundamental loads[J]. Composites Science and Technology,2017,152:149-158.
[4]	SUN F F, WANG P, LI W X, et al. Effects of circular cutouts on mechanical behaviors of carbon fiber reinforced lattice-core sandwich cylinder[J]. Composites Part A: Applied Science and Manufacturing,2017,100:313-323.
[5]	UMER R, BARSOUM Z, JISHI H Z, et al. Analysis of the compression behaviour of different composite lattice designs[J]. Journal of Composite Materials,2018,52(6):715-729. doi: 10.1177/0021998317714531
[6]	胡记强, 王兵, 张涵其, 等. 热塑性复合材料构件的制备及其在航空航天领域的应用[J]. 宇航总体技术, 2020, 4(4):61-70. HU Jiqiang, WANG Bing, ZHANG Hanqi, et al. Preparation of thermoplastic composite components and their application in aerospace field[J]. General Aerospace Technology,2020,4(4):61-70(in Chinese).
[7]	GIUSTO G, TOTARO G, SPENA P, et al. Composite grid structure technology for space applications[J]. Materials Today: Proceedings,2021,34:332-340. doi: 10.1016/j.matpr.2020.05.754
[8]	熊健, 李志彬, 刘惠彬, 等. 航空航天轻质复合材料壳体结构研究进展[J]. 复合材料学报, 2021, 38(6):1629-1650. XIONG Jian, LI Zhibin, LIU Huibin, et al. Advances in aerospace lightweight composite shell structure[J]. Acta Materiae Compositae Sinica,2021,38(6):1629-1650(in Chinese).
[9]	王晓旭, 张典堂, 钱坤, 等. 深海纤维增强树脂复合材料圆柱耐压壳力学性能的研究进展[J]. 复合材料学报, 2020, 37(1): 16-26. WANG Xiaoxu, ZHANG Diantang, QIAN Kun, et al. Research progress on mechanical properties of deep-sea fiber reinforced resin composite cylindrical pressure shells[J]. Acta Materiae Compositae Sinica, 2020, 37(1): 16-26(in Chinese).
[10]	MA Q, REJAB M R M, SIREGAR J P, et al. A review of the recent trends on core structures and impact response of sandwich panels[J]. Journal of Composite Materials,2021,55(18):2513-2555. doi: 10.1177/0021998321990734
[11]	AMIR E, HAMID D. Influence of employing laminated isogrid configuration on mechanical behavior of grid structures[J]. Journal of Reinforced Plastics and Composites,2019,38(16):518-601.
[12]	DAVOUD S G, GHOLAMHOSSEIN R, GHOLAMHOSSEIN L, et al. Buckling prediction of composite lattice sandwich cylinders (CLSC) through the vibration correlation technique (VCT): Numerical assessment with experimental and analytical verification[J]. Composites Part B: Engineering,2020,199:724-741.
[13]	LIU Z B, CHEN H T, XING S Q. Mechanical performances of metal-polymer sandwich structures with 3D-printed lattice cores subjected to bending load[J]. Archives of Civil and Mechanical Engineering,2020,20(3):649-667.
[14]	MENG L, LAN X, ZHAO J, et al. Failure analysis of bio-inspired corrugated sandwich structures fabricated by laser powder bed fusion under three-point bending[J]. Composite Structures,2021,263(1):113724.
[15]	HU K, LIN K, GU D, et al. Mechanical properties and deformation behavior under compressive loading of selective laser melting processed bio-inspired sandwich structures[J]. Materials Science and Engineering: A,2019,762:138089. doi: 10.1016/j.msea.2019.138089
[16]	杨爽, 彭志龙, 姚寅, 等. 龟壳角质层的微结构特征及拉伸力学性能[J]. 中国科学: 物理学, 力学, 天文学, 2020, 50(9):185-193. YANG Shuang, PENG Zhilong, YAO Yin, et al. The microstructure and tensile property of the cuticle of turtle shells[J]. Chinese Science: Physics, Mechanics, Astronomy,2020,50(9):185-193(in Chinese).
[17]	LI H, WANG X, HU X, et al. Vibration and damping study of multifunctional grille composite sandwich plates with an IMAS design approach[J]. Composites Part B: Engineering,2021,223:109078. doi: 10.1016/j.compositesb.2021.109078
[18]	PENG X, DAI Z, LIU J, et al. Design and simulation of sandwich structure of exoskeleton backplate based on biological inspiration[J]. Journal of Physics: Conference Series. IOP Publishing,2021,1885(5):052066. doi: 10.1088/1742-6596/1885/5/052066
[19]	THORSSON S I, WAAS A M, RASSAIAN M. Low-velocity impact predictions of composite laminates using a continuum shell based modeling approach part B: BVID impact and compression after impact[J]. International Journal of Solids and Structures,2018,155:201-212. doi: 10.1016/j.ijsolstr.2018.07.018
[20]	BOGENFELD R, KREIKEMEIER J, WILLE T. Review and benchmark study on the analysis of low-velocity impact on composite laminates[J]. Engineering Failure Analysis,2018,86:72-99. doi: 10.1016/j.engfailanal.2017.12.019
[21]	LE V T, SAN H N, GOO N S. Advanced sandwich structures for thermal protection systems in hypersonic vehicles: A review[J]. Composites Part B: Engineering,2021,226:109301. doi: 10.1016/j.compositesb.2021.109301
[22]	HU J, LIU A, ZHU S, et al. Novel panel-core connection process and impact behaviors of CF/PEEK thermoplastic composite sandwich structures with truss cores[J]. Composite Structures,2020,251:112659. doi: 10.1016/j.compstruct.2020.112659
[23]	张亚文, 陈秉智, 石姗姗, 等. 格栅-蜂窝混式芯体夹芯结构的低速冲击性能[J]. 复合材料学报, 2022, 39(1):381-389. doi: 10.1007/s10114-021-0023-4 ZHANG Yawen, CHEN Bingzhi, SHI Shanshan, et al. Low-velocity impact performance of grid-honeycomb hybrid core sandwich structure[J]. Acta Materiae Compositae Sinica,2022,39(1):381-389(in Chinese). doi: 10.1007/s10114-021-0023-4
[24]	ÖZEN İ, ÇAVA K, GEDIKLI H, et al. Low-energy impact response of composite sandwich panels with thermoplastic honeycomb and reentrant cores[J]. Thin-Walled Structures,2020,156:106989. doi: 10.1016/j.tws.2020.106989
[25]	卿彦, 廖宇, 刘婧祎, 等. 木基储能材料研究新进展[J]. 林业工程学报, 2021, 6(5):1-13. QING Yan, LIAO Yu, LIU Jingyi, et al. New research progress of wood-based energy storage materials[J]. Journal of Forestry Engineering,2021,6(5):1-13(in Chinese).
[26]	ROZYLO P. Experimental-numerical study into the stabi-lity and failure of compressed thin-walled composite profiles using progressive failure analysis and cohesive zone model[J]. Composite Structures,2021,257:113303. doi: 10.1016/j.compstruct.2020.113303
[27]	ZHOU S, LI Y, FU K, et al. Progressive fatigue damage modelling of fibre-reinforced composite based on fatigue master curves[J]. Thin-Walled Structures,2021,158:107173. doi: 10.1016/j.tws.2020.107173
[28]	NAGARAJ M H, REINER J, VAZIRI R, et al. Compressive damage modeling of fiber-reinforced composite laminates using 2D higher-order layer-wise models[J]. Composites Part B: Engineering,2021,215:108753. doi: 10.1016/j.compositesb.2021.108753
[29]	LIU J L, LIU J Y, MEI J, et al. Investigation on manufacturing and mechanical behavior of all-composite sandwich structure with Y-shaped cores[J]. Composites Science and Technology,2018,159:87-102. doi: 10.1016/j.compscitech.2018.01.026
[30]	DE CAMARGO F V, PAVLOVIC A, SCHENAL E C, et al. Explicit stacked-shell modelling of aged basalt fiber reinforced composites to low-velocity impact[J]. Composite Structures,2021,256:113017. doi: 10.1016/j.compstruct.2020.113017
[31]	LU T, CHEN X, WANG H. Predicting compression-after-impact behavior of thermoplastic composite laminates by an experiment-based approach[J]. Composites Science and Technology,2021,213:108952. doi: 10.1016/j.compscitech.2021.108952