(Me1/3Hf1/3Nb1/3)B2(Me=Ti, Zr, Ta)陶瓷的制备、显微结构和力学性能

许亮; 张岩; 张威; 郭伟明; 林华泰

doi:10.13801/j.cnki.fhclxb.20210906.002

(Me_1/3Hf_1/3Nb_1/3)B₂(Me=Ti, Zr, Ta)陶瓷的制备、显微结构和力学性能

doi: 10.13801/j.cnki.fhclxb.20210906.002

广东工业大学　机电工程学院，广州 510006

基金项目: 珠江新星项目(201710010142)

详细信息

通讯作者:
郭伟明，博士，教授，博士生导师，研究方向为超高温陶瓷　E-mail: guo1238@126.com

中图分类号: TG148
计量
- 文章访问数: 566
- HTML全文浏览量: 369
- PDF下载量: 102
- 被引次数: 0
出版历程
- 收稿日期: 2021-07-07
- 修回日期: 2021-08-09
- 录用日期: 2021-08-20
- 网络出版日期: 2021-09-06
- 刊出日期: 2022-07-30

Fabrication, microstructure and mechanical properties of (Me_1/3Hf_1/3Nb_1/3)B₂(Me=Ti, Zr, Ta) ceramics

School of Electromechanical Engineering, Guangdong University of Technology, Guangzhou 510006, China

摘要

摘要: 以采用硼热/碳热还原反应自合成的(Me_1/3Hf_1/3Nb_1/3)B₂ (Me=Ti, Zr, Ta) 为原料，通过放电等离子烧结制备了(Me_1/3Hf_1/3Nb_1/3)B₂陶瓷，系统研究了其相组成、致密度、显微结构和力学性能。结果表明，(Ti_1/3Hf_1/3Nb_1/3)B₂和(Zr_1/3Hf_1/3Nb_1/3)B₂陶瓷具有较高的致密度(~98%)，而(Ta_1/3Hf_1/3Nb_1/3)B₂陶瓷的致密度较低(~93%)。(Ti_1/3Hf_1/3Nb_1/3)B₂的晶粒较粗，而(Zr_1/3Hf_1/3Nb_1/3)B₂和(Ta_1/3Hf_1/3Nb_1/3)B₂的晶粒相对较小，并且在(Ta_1/3Hf_1/3Nb_1/3)B₂中Nb元素出现局部偏析。(Ti_1/3Hf_1/3Nb_1/3)B₂陶瓷具有较优异的力学性能，硬度和韧性分别为(20.08±0.81) GPa和(2.52±0.15) MPa·m^1/2，而(Zr_1/3Hf_1/3Nb_1/3)B₂陶瓷的力学性能较差，硬度和断裂韧性分别为(17.21±0.63) GPa和(1.50±0.18) MPa·m^1/2。
- 硼热/碳热还原法 /
- 硼化物陶瓷 /
- 固溶 /
- 显微结构 /
- 力学性能
Abstract: With (Me_1/3Hf_1/3Nb_1/3)B₂ (Me=Ti, Zr, Ta) powders self-synthesized via boron/carbothermal reduction, (Me_1/3Hf_1/3Nb_1/3)B₂ ceramics were prepared by spark plasma sintering (SPS), and their phase composition, relative density, microstructure and mechanical properties were investigated systematically. The result reveals that (Ti_1/3Hf_1/3Nb_1/3)B₂ and (Zr_1/3Hf_1/3Nb_1/3)B₂ possess the high relative density (~98%), while (Ta_1/3Hf_1/3Nb_1/3)B₂ has the lowest relative density (~93%). (Ti_1/3Hf_1/3Nb_1/3)B₂ possesses relatively coarse grains, while (Zr_1/3Hf_1/3Nb_1/3)B₂ and (Ta_1/3Hf_1/3Nb_1/3)B₂possess relatively fine grains and Nb segregation is found in (Ta_1/3Hf_1/3Nb_1/3)B₂. (Ti_1/3Hf_1/3Nb_1/3)B₂ shows the most excellent mechanical properties with the Vickers hardness and fracture toughness of (20.08±0.81) GPa and (2.52±0.15) MPa·m^1/2, respectively, whereas the mechanical properties of (Zr_1/3Hf_1/3Nb_1/3)B₂ are inferior, with hardness and fracture toughness of (17.21±0.63) GPa and (1.50±0.18) MPa·m^1/2, respectively.
- boron/carbothermal reduction /
- diboride ceramics /
- solid solution /
- microstructure /
- mechanical properties

HTML全文

图 1 2000℃烧结(Me_1/3Hf_1/3Nb_1/3)B₂ 陶瓷的XRD图谱：(a) (Ti_1/3Hf_1/3Nb_1/3)B₂；(b) (Zr_1/3Hf_1/3Nb_1/3)B₂；(c) (Ta_1/3Hf_1/3Nb_1/3)B₂

Figure 1. XRD patterns of (Me_1/3Hf_1/3Nb_1/3)B₂ ceramics sintered at 2000℃: (a) (Ti_1/3Hf_1/3Nb_1/3)B₂; (b) (Zr_1/3Hf_1/3Nb_1/3)B₂; (c) (Ta_1/3Hf_1/3Nb_1/3)B₂

下载: 全尺寸图片幻灯片

图 2 2000℃烧结(Me_1/3Hf_1/3Nb_1/3)B₂ 陶瓷SEM图像和相应的能谱元素图：(a) (Ti_1/3Hf_1/3Nb_1/3)B₂；(b) (Zr_1/3Hf_1/3Nb_1/3)B₂；(c) (Ta_1/3Hf_1/3Nb_1/3)B₂

Figure 2. SEM images and the corresponding EDS elemental mappings of (Me_1/3Hf_1/3Nb_1/3)B₂ ceramics sintered at 2000℃: (a) (Ti_1/3Hf_1/3Nb_1/3)B₂; (b) (Zr_1/3Hf_1/3Nb_1/3)B₂; (c) (Ta_1/3Hf_1/3Nb_1/3)B₂

下载: 全尺寸图片幻灯片

图 3 2000℃烧结(Me_1/3Hf_1/3Nb_1/3)B₂陶瓷材料腐蚀的SEM图像：(a) (Ti_1/3Hf_1/3Nb_1/3)B₂；(b) (Zr_1/3Hf_1/3Nb_1/3)B₂；(c) (Ta_1/3Hf_1/3Nb_1/3)B₂

Figure 3. SEM images of the polished surface of (Me_1/3Hf_1/3Nb_1/3)B₂ ceramics sintered at 2000℃ after acid etching: (a) (Ti_1/3Hf_1/3Nb_1/3)B₂; (b) (Zr_1/3Hf_1/3Nb_1/3)B₂; (c) (Ta_1/3Hf_1/3Nb_1/3)B₂

下载: 全尺寸图片幻灯片

图 4 2000℃烧结(Me_1/3Hf_1/3Nb_1/3)B₂ 陶瓷材料的裂纹扩展图像：(a) (Ti_1/3Hf_1/3Nb_1/3)B₂；(b) (Zr_1/3Hf_1/3Nb_1/3)B₂；(c) (Ta_1/3Hf_1/3Nb_1/3)B₂

Figure 4. Crack propagation images of (Me_1/3Hf_1/3Nb_1/3)B₂ ceramics sintered at 2000℃: (a) (Ti_1/3Hf_1/3Nb_1/3)B₂; (b) (Zr_1/3Hf_1/3Nb_1/3)B₂; (c) (Ta_1/3Hf_1/3Nb_1/3)B₂

下载: 全尺寸图片幻灯片

表 1 2000℃烧结(Me_1/3Hf_1/3Nb_1/3)B₂陶瓷的晶胞参数、相对密度、晶粒尺寸与力学性能

Table 1. Lattice parameters, relative density, grain size and mechanical properties of (Me_1/3Hf_1/3Nb_1/3)B₂ ceramics sintered at 2000℃

Code	a/nm	c/nm	Relative density/%	Grain size/μm	Hardness/ GPa	Fracture toughness/ (MPa·m^1/2)
(Ti_1/3Hf_1/3Nb_1/3)B₂	0.30919	0.33423	98.02	1.97±0.47	20.08±0.81	2.52±0.15
(Zr_1/3Hf_1/3Nb_1/3)B₂	0.31346	0.34384	98.35	1.67±0.43	17.21±0.63	1.50±0.18
(Ta_1/3Hf_1/3Nb_1/3)B₂	0.31076	0.33481	92.87	1.55±0.38	19.29±0.73	2.43±0.14
Notes: a and c—Lattice parameters of (Me_1/3Hf_1/3Nb_1/3)B₂ ceramics sintered at 2000℃.

下载: 导出CSV

参考文献(28)

[1]	FAHRENHOLTZ W G, HILMAS G E, TALMY I G, et al. Refractory diborides of zirconium and hafnium[J]. Journal of the American Ceramic Society,2007,90:1347-1364. doi: 10.1111/j.1551-2916.2007.01583.x
[2]	BROWN-SHAKLEE H J, FAHRENHOLTZ W G, HILMAS G E. Densification behavior and microstructure evolution of hot-pressed HfB₂[J]. Journal of the American Ceramic Society,2011,94:49-58. doi: 10.1111/j.1551-2916.2010.04063.x
[3]	彭易发, 李争显, 陈云飞, 等. 硼化物超高温陶瓷的研究进展[J]. 陶瓷学报, 2018, 39(2):9-16. PENG Yifa, LI Zhengxian, CHEN Yunfei, et al. Research progress of research progress of diboride UHTCS[J]. Journal of Ceramics,2018,39(2):9-16(in Chinese).
[4]	MONTEVERDE F, BELLOSIA A, SCATTEIA L. Processing and properties of ultra-high temperature ceramics for space applications[J]. Materials Science and Engineering: A,2008,485(1-2):415-421.
[5]	陈丽敏, 索相波, 王安哲, 等. ZrB₂基超高温陶瓷材料抗热震性能及热震失效机制研究进展[J]. 硅酸盐学报, 2018, 46(9):1235-1243. CHEN Limin, SUO Xiangbo, WANG Anzhe, et al. Thermal shock resistance and failure mechanism of ZrB₂-based ultra-high temperature ceramic composites—A short review[J]. Journal of the Chinese Ceramic Society,2018,46(9):1235-1243(in Chinese).
[6]	SCITI D, SILVESTRONI L, NYGREN M. Spark plasma sintering of Zr- and Hf-borides with decreasing amounts of MoSi₂ as sintering aid[J]. Journal of the European Ceramic Society,2018,28(6):1287-1296.
[7]	GUO S Q, YANG J M, TANAKA H, et al. Effect of thermal exposure on strength of ZrB₂-based composites with nano-sized SiC particles[J]. Composites Science and Technology,2008,68(14):3033-3040. doi: 10.1016/j.compscitech.2008.06.021
[8]	赵笑统, 赵新阳, 李智强, 等. Mo–Si–B对ZrB₂超高温陶瓷烧结工艺和性能的影响[J]. 硅酸盐学报, 2018, 46(3):382-387. ZHAO Xiaotong, ZHAO Xinyang, LI Zhiqiang, et al. Effect of Mo–Si–B on sintering process and properties of ZrB₂ ultra-high-temperature ceramics[J]. Journal of the Chinese Ceramic Society,2018,46(3):382-387(in Chinese).
[9]	王晓玲, 王周福, 王玺堂, 等. 熔盐中镁热还原合成二硼化钛纳米粉体[J]. 硅酸盐学报, 2014, 42(6):709-713. WANG Xiaoling, WANG Zhoufu, WANG Xitang, et al. Synthesis of TiB₂ nanopowder by magnesiothermic reduction in molten salt[J]. Journal of the Chinese Ceramic Society,2014,42(6):709-713(in Chinese).
[10]	ZHANG Y, TAN D W, GUO W M, et al. Improvement of densification and microstructure of HfB₂ ceramics by Ta/Ti substitution for Hf[J]. Journal of the American Ceramic Society,2019,103:103-111.
[11]	GUO W M, TAN D W, ZENG L Y, et al. Synthesis of fine ZrB₂ powders by solid solution of TaB₂ and their densification and mechanical properties[J]. Ceramics International,2018,44:4473-4477.
[12]	CHAKRABORTY S, DEBNATH D, MALLICK A R, et al. Mechanical and thermal properties of hot pressed ZrB₂ system with TiB₂[J]. International Journal of Refractory Metals and Hard Materials,2014,46:35-42. doi: 10.1016/j.ijrmhm.2014.05.004
[13]	FENG L, FAHRENHOLTZ W G, HILMAS G E, et al. Effect of Nb content on the phase composition, densification, microstructure, and mechanical properties of high-entropy boride ceramics[J]. Journal of the European Ceramic Society,2021,41:92-100. doi: 10.1016/j.jeurceramsoc.2020.08.058
[14]	ZHAO X T, WANG H L, SHAO G, et al. Processing and properties of (Zr, Hf)B₂-SiC ceramic composites[J]. Solid State Phenomena,2018,281:438-443. doi: 10.4028/www.scientific.net/SSP.281.438
[15]	MCCLANE D L, FAHRENHOLTZ W G, HILMAS G E. Thermal properties of (Zr, TM)B₂ solid solutions with TM=Ta, Mo, Re, V, and Cr[J]. Journal of the American Ceramic Society,2015,98(2):637-644. doi: 10.1111/jace.13341
[16]	MCCLANE D L, FAHRENHOLTZ W G, HILMAS G E. Thermal properties of (Zr, TM)B₂ solid solutions with TM = Hf, Nb, W, Ti, and Y[J]. Journal of the American Ceramic Society,2014,97(5):1552-1558. doi: 10.1111/jace.12893
[17]	中国国家标准化管理委员会. 精细陶瓷室温硬度试验方法: GB/T 16534—2009[S]. 北京: 中国标准出版社, 2009. Standardization Administration of the People’s Republic of China. Fine ceramics (advanced ceramics advanced technical ceramics)—Test method for hardness of monolithic ceramics at room temperature: GB/T 16534—2009[S]. Beijing: China Standards Press, 2009(in Chinese).
[18]	EVANS A G, CHARLES E A. Fracture toughness determinations by indentation[J]. Journal of the American Ceramic Society,1976,59:371-372. doi: 10.1111/j.1151-2916.1976.tb10991.x
[19]	SHARMA S K, BANERJEE S, KULDEEP, et al. Some correlations for diffusion in amorphous alloys[J]. Journal of Materials Research,1989,4:603-606. doi: 10.1557/JMR.1989.0603
[20]	HE Y, PENG C, XIN S, et al. Vacancy effect on the preparation of high-entropy carbides[J]. Journal of Materials Science,2020,55(16):6754-6760. doi: 10.1007/s10853-020-04471-3
[21]	RAJU G B, BASU B, TAK N H, et al. Temperature dependent hardness and strength properties of TiB₂ with TiSi₂ sinter-aid[J]. Journal of the European Ceramic Society,2009,29(10):2119-2128. doi: 10.1016/j.jeurceramsoc.2008.11.018
[22]	SCHNEIDER S J. Engineered materials handbook volume 4: Ceramics and glasses[M]. Almere: ASM International, 1991: 787-803.
[23]	LICHERI R, MUSA C, ORRU R, et al. Silvestroni, bulk monolithic zirconium and tantalum diborides by reactive and non-reactive spark plasma sintering[J]. Journal of Alloys and Compounds,2016,663:351-359. doi: 10.1016/j.jallcom.2015.12.096
[24]	HUANG P K, YEH J W. Effects of substrate bias on structure and mechanical properties of (AlCrNbSiTiV)N coatings[J]. Journal of Physics D: Applied Physics,2009,42:115401. doi: 10.1088/0022-3727/42/11/115401
[25]	TIAN F, VARGA L K, CHEN N, et al. Empirical design of single phase high-entropy alloys with high hardness[J]. Intermetallics,2015,58:1-6. doi: 10.1016/j.intermet.2014.10.010
[26]	YANG Y, WANG W, GAN G, et al. Structural, mechanical and electronic properties of (TaNbHfTiZr)C high entropy carbide under pressure: Ab initio investigation[J]. Physica B: Physics of Condensed Matter,2018,550:163-170. doi: 10.1016/j.physb.2018.09.014
[27]	YANG Y, MA L, GAN G Y, et al. Investigation of thermodynamic properties of high entropy (TaNbHfTiZr)C and (TaNbHfTiZr)N[J]. Journal of Alloys and Compounds,2019,788:1076-1083. doi: 10.1016/j.jallcom.2019.02.254
[28]	YE B, WEN T, NGUYEN M C, et al. First-principles study, fabrication and characterization of (Zr_0.25Nb_0.25Ti_0.25V_0.25)C high-entropy ceramics[J]. Acta Materialia,2019,170:15-23. doi: 10.1016/j.actamat.2019.03.021